G-Lift Fixing Sockets, M8 to M24

Spherical-head anchors for lifting precast slabs, beams, pipes and thin elements, in seven load groups.

• Spherical head, one-motion attachment
• Load groups 1.3 to 20 tonne
• Lengths from 85 to 250 mm

Threaded lifting loops with a welded eye and retracted rope loop, in six Rd sizes from 1.2 to 8 tonne.

• Rd 16 to Rd 42 threads
• Load 1.2 to 8 tonne
• Welded eye, retracted rope loop

Steel lifting shackles for ball-head and spherical-head anchors, in six load groups from 1.3 to 20 tonne.

• Six load groups, 1.3 to 20 tonne
• For spherical-head anchor systems
• Breakage safety factor of 5

Cast-in lifting sockets with a cross-hole for reinforcement bar and a plastic stopper that keeps concrete out of the thread.

• Rd 12 to Rd 52 thread sizes
• Cross-hole for reinforcement bar
• Safe Load 500 to 12,500 kg

Reusable natural-rubber recess formers that create the pocket around a lifting anchor in precast formwork.

• Natural rubber, reusable
• Round and TPA shapes
• Matched to load groups

Heat-treated ring clutches with a T-slot for dogbone anchors, in five load groups from 1.2 to 26 tonne.

• Five load groups, 1.2 to 26 tonne
• T-slot engages dogbone anchors
• Manual locking bolt, no tools

Steel spread anchors for lifting precast slabs and panels, resisting both shear and tension loads.

• Seven sizes, 2.5 T to 10 T
• Resists shear and tension loads
• Plain, electro or hot-dip galvanized

Wire-rope lifting loops with an externally threaded steel ferrule, in ten RD thread sizes from 5 kN to 125 kN.

• Ten RD thread sizes
• Load 5 kN to 125 kN
• Externally threaded steel ferrule

Anchors for lifting thin or low-compressive-strength concrete panels, with two holes for an additional rebar or tension bar.

• Six sizes from 2.5 T to 22 T
• Two-hole design takes extra rebar
• For thin or low-strength panels

Polymer recess closures that seal lifting socket recesses in precast elements and protect the sockets from dirt, water and corrosion.

• Plastic caps that seal socket recesses
• Protect socket threads from corrosion
• Seven sizes from 12 to 42 mm

Colour-coded plates that hold lifting sockets in position on formwork while precast concrete is poured and cured.

• Holds lifting sockets on formwork
• Colour-coded by size
• Plates for 12 to 42 mm sockets

Diamond saw blades for every class of cutting machine, specified by material and machine power for reinforced concrete, asphalt, masonry, stone, tiles and precast.

• Blades for hand-held, floor and wall saws
• Concrete, asphalt, stone and tile cutting
• Specified by machine power and material

Single wire loops that pop up after casting for wall-to-wall and wall-to-column connections in precast construction.

• Single wire loop, 1770 MPa
• Sizes from 80 to 140 mm
• Pop-up loop, no re-bending

Polymer clip spacers that hold horizontal reinforcement at a defined concrete cover, specified to German Performance Class L2 (1 kN).

• Clip-fit support for horizontal rebar
• Cover sizes from 20 to 75 mm
• German performance class L2 (1 kN)

Polymer spacers that lift rooftop and patio tiles to a uniform height, so water drains and the waterproofing layer is protected.

• Raise tiles for drainage
• Protect waterproofing layers
• Heights of 13 and 19 mm

An SDS-plus dual-cutter hammer drill bit for concrete and reinforcement steel, with a patented drill head and a helix built to carry drilling dust out of the hole.

• Dual-cutter for concrete and rebar
• Twinmax 3D helix clears drilling dust
• Sizes from 4 to 26 mm

Chisels for SDS rotary hammers, in the shapes and sizes that demolition, chasing and refurbishment work in concrete, masonry and stone call for.

• SDS-plus and SDS-max chisels
• Types for demolition, chasing and tiles
• Tool steel chisels, can be reground

Zinc-coated steel single step with a 12 mm core and a 145 mm dowel distance.

• Zinc-coated steel single step
• 12 mm core, 0.800 kg
• Dowel distance 145 mm

Inverter electrofusion control unit with an actively cooled aluminium housing, intended for demanding large-diameter couplers.

• Inverter electrofusion control unit
• 8–48 V DC output
• Couplers up to 1200 mm and above

Automatic butt fusion machine for pipe from 450 to 800 mm, with a 0–16 MPa hydraulic range and an integrated 0.5 kW crane.

• Automatic butt fusion, 450–800 mm
• Pressure range 0–16 MPa
• Integrated crane, 1360 kg

A 2300 W electric pipe cutter for pipe from 75 to 400 mm, with variable speed and a tool-free blade lock.

• Cuts pipe 75 to 400 mm
• 2300 W, 0–2900 r/min
• One-click blade lock

A 3000 W hand extruder for PE and PP welding in civil engineering, tank fabrication and membrane work.

• Longer-body extruder for civil engineering
• Welds HDPE, LDPE, LLDPE and PP
• Overlap welding shoe included

A compact hot wedge welding machine for clean, consistent overlap seams in tarpaulins, banners, awnings and other thin membranes.

• Hot wedge welder for 0.1–1 mm membranes
• Tarpaulins, banners, awnings and covers
• 3.6 kg, up to 7.5 m/min