G-Lift Plastic and Steel Chamfer Strips, 5 to 30 mm

Cast-in anchor channels with T-bolts for adjustable fixings that avoid drilling into hardened concrete.

• Five C-channel profile sizes
• T-bolts M10 to M20
• Cast-in, no on-site drilling

Single wire loops that pop up after casting for wall-to-wall and wall-to-column connections in precast construction.

• Single wire loop, 1770 MPa
• Sizes from 80 to 140 mm
• Pop-up loop, no re-bending

High-strength steel connector pins for joining the layers of precast sandwich panels.

• For precast sandwich panels
• Four sizes, 150 to 250 mm
• High-strength steel pins

Galvanized steel corrugated pipes in diameters from 40 to 150 mm for post-tensioning ducts, voids and service penetrations.

• Galvanized steel, 40 to 150 mm
• Hot-dip galvanized coating
• Bendable, cuttable, semi-rigid

Mechanical expansion bolts for post-fixing in concrete, in seven sizes from M6 to M24.

• Sizes M6 to M24
• Mild steel, silver or zinc-plated
• Recommended tensile and shear loads

Hex nuts for steel tie rods in formwork and shuttering, for 15 mm and 20 mm bars.

• For 15 and 20 mm tie rods
• Five lengths, 50 to 130 mm
• Weights from 0.22 to 0.78 kg

A styrene-free, two-component pure epoxy anchoring system for fixings in concrete, stone and masonry.

• Two-component pure epoxy, 3:1
• Styrene-free and odourless
• Concrete, stone and masonry

A manufacturing service for plastic components made to your specification, from concept and tooling through to production and finishing.

• Custom plastic components to specification
• Design, tooling and production support
• Prototypes to high-volume runs

Zinc-coated steel handbar with plastic encapsulation and a 230 mm leg length.

• Steel handbar with zinc coating
• Leg length 230 mm, 1.150 kg
• Horizontal pullout approx. 440 kg

Zinc-coated steel handbar with plastic encapsulation and a short 170 mm leg length.

• Zinc-coated steel handbar
• Leg length 170 mm, 0.850 kg
• Vertical pullout approx. 440 kg

Polymer end caps that seal the open cores of hollow core slabs during grouting, storage and transport.

• End caps for hollow core slabs
• Keep grout out of the cores
• Six slab sizes, 150 to 500 mm

Moulded polymer chamfer profiles that form clean, consistent chamfered edges and groove lines in precast and cast-in-situ concrete.

• Forms clean chamfered concrete edges
• Four sizes from 10 to 25 mm
• Supplied in 2 m lengths

Diamond saw blades for every class of cutting machine, specified by material and machine power for reinforced concrete, asphalt, masonry, stone, tiles and precast.

• Blades for hand-held, floor and wall saws
• Concrete, asphalt, stone and tile cutting
• Specified by machine power and material

Flat-end fixing sockets with a cross-hole, in six metric sizes for lightweight precast elements and wooden formwork.

• Thread sizes M8 to M24
• Crimped flat end with cross-hole
• SWL 200 to 1600 kg

Single wire loops that pop up after casting for wall-to-wall and wall-to-column connections in precast construction.

• Single wire loop, 1770 MPa
• Sizes from 80 to 140 mm
• Pop-up loop, no re-bending

Polymer clip spacers that hold horizontal reinforcement at a defined concrete cover, specified to German Performance Class L2 (1 kN).

• Clip-fit support for horizontal rebar
• Cover sizes from 20 to 75 mm
• German performance class L2 (1 kN)

Polymer spacers that lift rooftop and patio tiles to a uniform height, so water drains and the waterproofing layer is protected.

• Raise tiles for drainage
• Protect waterproofing layers
• Heights of 13 and 19 mm

An SDS-plus dual-cutter hammer drill bit for concrete and reinforcement steel, with a patented drill head and a helix built to carry drilling dust out of the hole.

• Dual-cutter for concrete and rebar
• Twinmax 3D helix clears drilling dust
• Sizes from 4 to 26 mm

Chisels for SDS rotary hammers, in the shapes and sizes that demolition, chasing and refurbishment work in concrete, masonry and stone call for.

• SDS-plus and SDS-max chisels
• Types for demolition, chasing and tiles
• Tool steel chisels, can be reground

Zinc-coated steel single step with a 12 mm core and a 145 mm dowel distance.

• Zinc-coated steel single step
• 12 mm core, 0.800 kg
• Dowel distance 145 mm

Inverter electrofusion control unit with an actively cooled aluminium housing, intended for demanding large-diameter couplers.

• Inverter electrofusion control unit
• 8–48 V DC output
• Couplers up to 1200 mm and above

Automatic butt fusion machine for pipe from 450 to 800 mm, with a 0–16 MPa hydraulic range and an integrated 0.5 kW crane.

• Automatic butt fusion, 450–800 mm
• Pressure range 0–16 MPa
• Integrated crane, 1360 kg

A 2300 W electric pipe cutter for pipe from 75 to 400 mm, with variable speed and a tool-free blade lock.

• Cuts pipe 75 to 400 mm
• 2300 W, 0–2900 r/min
• One-click blade lock

A 3000 W hand extruder for PE and PP welding in civil engineering, tank fabrication and membrane work.

• Longer-body extruder for civil engineering
• Welds HDPE, LDPE, LLDPE and PP
• Overlap welding shoe included

A compact hot wedge welding machine for clean, consistent overlap seams in tarpaulins, banners, awnings and other thin membranes.

• Hot wedge welder for 0.1–1 mm membranes
• Tarpaulins, banners, awnings and covers
• 3.6 kg, up to 7.5 m/min