Moulded polymer chamfer profiles that form clean, consistent chamfered edges and groove lines in precast and cast-in-situ concrete.
- Forms clean chamfered concrete edges
- Four sizes from 10 to 25 mm
- Supplied in 2 m lengths
Explore the category
Precast & Construction Accessories
Accessories used in precast production and construction detailing: forming edges and recesses, connecting panels, fixing to concrete, levelling elements and fitting out chambers.
Product types and selection
Product Types
- Forming accessories: plastic and steel chamfers, rebar cones, hollow core caps and corrugated ducts.
- Connection and anchoring: connecting loops, connector pins, cast-in channels and T-bolts, expansion bolts and adhesive anchors.
- Levelling and packing: shim pads and U-shim pads for precast and steel erection, and roof tile spacers for raised paving.
- Formwork hardware: hex nuts for tie rods.
- Manhole steps and handbars: plastic-encapsulated steps, rungs and handbars for underground chambers.
- Custom components: plastic parts made to drawing or sample.
Choosing Accessories
Each accessory is selected against the detail it serves: the edge or recess size, the connection design, the bearing height, or the chamber layout. Structural fixings and connections follow the project design loads.
Products in this category
13–18 of 21 products
Precision-moulded cones that form clean, uniform recesses in concrete for grouting and can be extracted after the formwork is removed.
- Cones that form grouting recesses
- Easy extraction after formwork removal
- Listed for 20, 22 and 26 mm
Polymer spacers that lift rooftop and patio tiles to a uniform height, so water drains and the waterproofing layer is protected.
- Raise tiles for drainage
- Protect waterproofing layers
- Heights of 13 and 19 mm
Square polymer shim pads for packing, levelling and aligning precast concrete elements during erection.
- Polymer pads for precast levelling
- Four thicknesses from 2 to 10 mm
- Square 70 x 70 mm pads
Zinc-coated steel manhole step with plastic encapsulation, listed as an A Type step with a 330 mm dowel distance.
- Steel step with zinc coating
- 16 mm core, 1.35 kg
- Vertical pullout approx. 370 kg
Zinc-coated steel single step with a 12 mm core and a 145 mm dowel distance.
- Zinc-coated steel single step
- 12 mm core, 0.800 kg
- Dowel distance 145 mm
A styrene-free, two-component pure epoxy anchoring system for fixings in concrete, stone and masonry.
- Two-component pure epoxy, 3:1
- Styrene-free and odourless
- Concrete, stone and masonry
Cast-in anchor channels with T-bolts for adjustable fixings that avoid drilling into hardened concrete.
- Five C-channel profile sizes
- T-bolts M10 to M20
- Cast-in, no on-site drilling
Plastic and steel chamfer strips for forming chamfered concrete edges and false joints, 5 to 30 mm.
- Plastic and steel chamfer strips
- Sizes 5 to 30 mm
- All strips 2 m long
Single wire loops that pop up after casting for wall-to-wall and wall-to-column connections in precast construction.
- Single wire loop, 1770 MPa
- Sizes from 80 to 140 mm
- Pop-up loop, no re-bending
High-strength steel connector pins for joining the layers of precast sandwich panels.
- For precast sandwich panels
- Four sizes, 150 to 250 mm
- High-strength steel pins
Galvanized steel corrugated pipes in diameters from 40 to 150 mm for post-tensioning ducts, voids and service penetrations.
- Galvanized steel, 40 to 150 mm
- Hot-dip galvanized coating
- Bendable, cuttable, semi-rigid
A manufacturing service for plastic components made to your specification, from concept and tooling through to production and finishing.
- Custom plastic components to specification
- Design, tooling and production support
- Prototypes to high-volume runs
Mechanical expansion bolts for post-fixing in concrete, in seven sizes from M6 to M24.
- Sizes M6 to M24
- Mild steel, silver or zinc-plated
- Recommended tensile and shear loads
Zinc-coated steel handbar with plastic encapsulation and a 230 mm leg length.
- Steel handbar with zinc coating
- Leg length 230 mm, 1.150 kg
- Horizontal pullout approx. 440 kg
Zinc-coated steel handbar with plastic encapsulation and a short 170 mm leg length.
- Zinc-coated steel handbar
- Leg length 170 mm, 0.850 kg
- Vertical pullout approx. 440 kg
Hex nuts for steel tie rods in formwork and shuttering, for 15 mm and 20 mm bars.
- For 15 and 20 mm tie rods
- Five lengths, 50 to 130 mm
- Weights from 0.22 to 0.78 kg
Polymer end caps that seal the open cores of hollow core slabs during grouting, storage and transport.
- End caps for hollow core slabs
- Keep grout out of the cores
- Six slab sizes, 150 to 500 mm
Zinc-coated steel manhole step with reflectors, listed as a B Type step with a 330 mm dowel distance.
- Zinc-coated steel step, reflectors
- B Type, 1.47 kg
- Vertical pullout approx. 520 kg
Pipe and cable holding rung with plastic encapsulation and a 12 mm core, listed as a B Type product.
- Pipe and cable holding rung
- 12 mm core, 0.930 kg
- Vertical pullout approx. 435 kg
Open-sided U-shaped packing shims that slot in around bolts and plates, for fast levelling in precast and steel erection.
- Open U shape fits around bolts
- Six thicknesses from 1 to 10 mm
- For precast and steel erection
No products match your selection.
Try another product name or clear the filters to browse the full selection.
Plan your purchase
Discuss your requirements
Contact Global Source Middle East about precast & construction accessories or request a quotation for your requirements.