Colour-coded plates that hold lifting sockets in position on formwork while precast concrete is poured and cured.
- Holds lifting sockets on formwork
- Colour-coded by size
- Plates for 12 to 42 mm sockets
Explore the category
Precast Lifting Systems
Cast-in anchors and the lifting equipment that connects to them, for lifting, turning and placing precast concrete elements, together with the formers and accessories used to cast them in.
Product types and selection
Product Types
- Lifting sockets and anchors: threaded lifting sockets, fixing sockets, capstan, spread and two-hole anchors cast into precast elements.
- Lifting equipment: threaded lifting loops, Goliath lifting loops, lifting shackles and ring clutches.
- Recess formers: reusable formers that create the anchor recess in the formwork.
- Socket accessories: nailing plates that hold sockets on the formwork and caps that close the finished recess.
Choosing a System
Anchor, lifting device and former are chosen together by load group or thread size. Pair each lifting device with an anchor of the correct load capacity, and size anchors against the lifting design for the element.
Products in this category
7–12 of 12 products
Reusable natural-rubber recess formers that create the pocket around a lifting anchor in precast formwork.
- Natural rubber, reusable
- Round and TPA shapes
- Matched to load groups
Heat-treated ring clutches with a T-slot for dogbone anchors, in five load groups from 1.2 to 26 tonne.
- Five load groups, 1.2 to 26 tonne
- T-slot engages dogbone anchors
- Manual locking bolt, no tools
Steel spread anchors for lifting precast slabs and panels, resisting both shear and tension loads.
- Seven sizes, 2.5 T to 10 T
- Resists shear and tension loads
- Plain, electro or hot-dip galvanized
Wire-rope lifting loops with an externally threaded steel ferrule, in ten RD thread sizes from 5 kN to 125 kN.
- Ten RD thread sizes
- Load 5 kN to 125 kN
- Externally threaded steel ferrule
Anchors for lifting thin or low-compressive-strength concrete panels, with two holes for an additional rebar or tension bar.
- Six sizes from 2.5 T to 22 T
- Two-hole design takes extra rebar
- For thin or low-strength panels
Spherical-head anchors for lifting precast slabs, beams, pipes and thin elements, in seven load groups.
- Spherical head, one-motion attachment
- Load groups 1.3 to 20 tonne
- Lengths from 85 to 250 mm
Flat-end fixing sockets with a cross-hole, in six metric sizes for lightweight precast elements and wooden formwork.
- Thread sizes M8 to M24
- Crimped flat end with cross-hole
- SWL 200 to 1600 kg
Threaded lifting loops with a welded eye and retracted rope loop, in six Rd sizes from 1.2 to 8 tonne.
- Rd 16 to Rd 42 threads
- Load 1.2 to 8 tonne
- Welded eye, retracted rope loop
Steel lifting shackles for ball-head and spherical-head anchors, in six load groups from 1.3 to 20 tonne.
- Six load groups, 1.3 to 20 tonne
- For spherical-head anchor systems
- Breakage safety factor of 5
Polymer recess closures that seal lifting socket recesses in precast elements and protect the sockets from dirt, water and corrosion.
- Plastic caps that seal socket recesses
- Protect socket threads from corrosion
- Seven sizes from 12 to 42 mm
Cast-in lifting sockets with a cross-hole for reinforcement bar and a plastic stopper that keeps concrete out of the thread.
- Rd 12 to Rd 52 thread sizes
- Cross-hole for reinforcement bar
- Safe Load 500 to 12,500 kg
No products match your selection.
Try another product name or clear the filters to browse the full selection.
Plan your purchase
Discuss your requirements
Contact Global Source Middle East about precast lifting systems or request a quotation for your requirements.